
Why Is Your Air Rock Loader Losing Power?
When a пневматический каменный погрузчик loses power, the cause is usually the air reaching the machine, not the machine itself. Air motors give full torque only when the pressure at the loader stays inside the working range, 0.45–0.7 MPa for the ZQ-17 and ZQ-26, while the bucket is lifting a full load. Too little air volume, a long or leaking hose, water and dirt in the line, poor lubrication and ice in the exhaust all pull that pressure down. Check these first, in this order, and only then look at the control valves, the air motors and mechanical drag.

Pin Down What Kind of Power Loss You Have
“Losing power” can mean different things, and each points to a different part of the machine. Note exactly what the loader does before changing any parts:
Symptom | Most likely cause | Check first |
Travel and bucket both weak | Low pressure or not enough air volume at the loader | Pressure at the loader inlet while lifting a full bucket |
Strong at the start of the shift, weak later | More air users on the line, water building up, exhaust icing | Compare pressure early and mid-shift; drain water; look at the exhaust |
Bucket weak, travel normal | Bucket control valve, lift air motor, chain or bucket linkage | Valve operation and lift motor exhaust; chain tension |
Travel weak, bucket normal | Travel motor, wheel or axle drag, track condition, gradient | Rails, wheel bearings, gradient of the track |
Jerky or uneven movement | Water in the air, sticking valve, poor lubrication | Drain water; check the oiler; inspect the valve |
Frost on the exhaust, power fades over time | Ice forming in the exhaust | Clear the exhaust; remove water from the air |
Weak, noisy, strong exhaust blow | Worn internal parts in an air motor | Air motor inspection or overhaul |
If the main complaint is a slow bucket rather than general weakness, our guide to a slow-moving bucket walks through the air path step by step.
Step 1: Measure Air Pressure at the Loader, Under Load
The gauge on the compressor shows pressure at the receiver, not at the machine. What decides power is the pressure at the loader inlet while it works. Fit a gauge at the inlet, or read the loader’s own gauge, and watch it while the bucket lifts a full load. A reading taken with the loader standing still hides the problem, because no air is flowing.
If the pressure stays inside the working range while lifting, the air supply is probably fine; go to Step 3. If it drops below 0.45 MPa as the bucket lifts, the loader is starved of air; go to Step 2. Air motor torque falls as pressure falls, so a loader working at the bottom of the range has clearly less digging force than one at the top.
Модель | Working pressure | Travel motor | Lift motor |
0.45–0.86 MPa | 9 kW | 9 kW | |
0.45–0.7 MPa | 11 kW | 15 kW | |
0.45–0.7 MPa | 11 kW | 15 kW |
Figures from our product pages. Measure at the loader, not at the compressor.
If the gauge itself climbs slowly when the air is turned on, see why the pressure gauge rises slowly.
Step 2: Check Air Volume and the Hose Run
Pressure drops under load when the loader uses air faster than the supply can deliver it. Work through these points:
- Compressor output against demand.The lift motor is the largest user. On the ZQ-13, for example, manufacturer data gives up to 15.6 m³/min of free air for the lift motor and up to 11.7 m³/min for each travel motor. If the compressor cannot deliver that while the bucket lifts, pressure collapses exactly when power is needed.
- Other users on the same line.Rock drills, pumps and blowpipes working at the same time take air from the loader. Stagger the work or give the loader its own supply.
- Hose length and size.A long, narrow hose, many couplings, reducers and kinks all cost pressure. Run the shortest practical hose of the correct size from the main line to the loader, and keep it out from under the wheels and loose rock.
Leaks. With the loader stopped and the line under pressure, listen along the hose and spray soapy water on the couplings. Every hissing joint wastes air for the whole shift.

Step 3: Remove Water and Dirt, and Get Lubrication Right
Compressed air cools on its way underground and drops water. Water washes the oil out of the air motors, causes rust and makes valves stick, and dirt in the line blocks the inlet strainer. Air motors also need a steady oil mist to keep their internal parts from wearing:
- Drain the water separator at the start of every shift, and more often in wet workings.
- Clean the inlet filter or strainer at least once a week, more often if the air is dirty.
- Check the line oiler every shift. It must hold oil, and the level must actually go down; if it does not, the motors are running dry.
- Use the lubricating oil given in the operating manual. Too much oil can gum up the valves, so set the oiler instead of simply filling it.
Step 4: Clear Ice and Blockages from the Exhaust
Air cools sharply as it expands through the motors. In humid mines the moisture can freeze in the exhaust ports and mufflers, restricting the flow out of the motor. The typical sign is power that fades during long periods of work and comes back after a stop. Removing water upstream (Step 3) is the real cure; in the meantime keep the exhaust mufflers clean and never block or wrap them.
Step 5: Inspect the Control Valves and Air Motors
Move on to the machine only when the pressure at the loader is right under load.
- Control valves.If one function is weak and the others are normal, check that the lever opens the valve fully. Play in the linkage, worn seals or dirt inside the valve can stop it from passing full flow. Clean it, replace worn seals and test again. Our article on stiff or sluggish controls covers this in more detail.
- Air motors.As the internal parts of an air motor wear, air leaks past them instead of doing work. The motor exhausts more air, gives less torque and is often noisier. If one motor is clearly weaker than the other under the same pressure, it needs an overhaul or a replacement.
Step 6: Rule Out Mechanical Drag and Site Conditions
A loader with a healthy air system can still feel weak if something mechanical is holding it back:
- Bucket lifting chain too loose or too tight; worn pins and linkages
- Wheel or axle bearings that drag; rails out of gauge, with bad joints or covered in rock
- Track steeper than the 5° operating limit of our rail models
Oversize or poorly blasted rock, or digging too high into the pile

When the Loader Is Simply Too Small for the Job
If every check passes and the loader still struggles, it may be working beyond its size. The ZQ-17 (0.17 m³ bucket) and ZQ-26 (0.26 m³ bucket) suit larger headings than the ZQ-13. For trackless workings there are wheel-type models such as the ZQW-13 и QZ-17, and where compressed air is limited an электрический погрузчик removes the dependence on the air supply altogether.
Common mistakes we see when power drops:
- Reading the pressure at the compressor instead of at the loader
- Testing the pressure with the loader standing still
- Adding more drills to the same air line
- Using a long, narrow hose with several reducers
- Skipping the water drain or letting the oiler run empty
- Replacing an air motor before checking the air supply
FAQ
What air pressure does a пневматический каменный погрузчик need?
Our ZQ-17 and ZQ-26 work at 0.45–0.7 MPa and the ZQ-13 at 0.45–0.86 MPa. What counts is the pressure measured at the loader while it is working, not the reading at the compressor.
Why is my loader strong at the start of the shift but weak later?
Usually more air users have come onto the line, water has built up in the hose and motors, or ice is forming in the exhaust. Compare the pressure at the loader early and in the middle of the shift.
How often should I drain the water separator?
At least at the start of every shift, and whenever you see water at the exhaust. Wet mines may need it several times per shift.
Will a bigger compressor fix the problem?
Only if air volume is the cause. If the hose is too long or too narrow, or the line leaks, a bigger compressor will not fully solve it. Measure the pressure at the loader first.
When does an air motor need an overhaul?
When the pressure and volume at the loader are correct, the valves work properly and the motor is still weak, with a strong exhaust blow or more noise than usual.
Related Products and Information
- Rail type air пневматический каменный погрузчикs: all rail models
- ZQ-13 air rock loader, ZQ-17 air rock loaderи ZQ-26 пневматический каменный погрузчик
- Wheel type air пневматический каменный погрузчикs
- пневматический каменный погрузчикbucket moves slowly: air system maintenance guide
- Why does the pressure on the air pressure gauge rise slowly?
- Common problems of underground пневматический каменный погрузчикs
- ZQ-26 air loader at work in an African underground mine
Still Short of Power? Send Us Your Readings
Tell us the loader model, the pressure at the compressor and at the пневматический каменный погрузчик while the bucket is lifting, the compressor’s air delivery, the length and diameter of the supply hose and what else runs on the same line. A short video of the machine working helps a lot. Our engineers will help you find the cause and, if needed, supply the right parts.







